My 1994 Honda Prelude Si, named Ceras Victoria, has been gone for over three years now.
But, in preparation for a long term ownership review of my 2014 Subaru BRZ, Cagalli Yula, which is long overdue now, I thought I would try my best at incorporating spreadsheets into a Blogger post. This is a first for me.
The car back in happier days when I only owned a properly crappy cell phone with a not very good camera...
As follows are some of the spreadsheets I keep for each of my vehicles.
Search This Blog
Showing posts with label Ceras Victoria. Show all posts
Showing posts with label Ceras Victoria. Show all posts
Saturday, September 30, 2017
Sunday, May 25, 2014
Ceras Victoria (Honda Prelude), Salvage (Part VII), Scrapping
Saturday, May 24, 2014
Friday, May 23, 2014
Friday, February 7, 2014
Sunday, February 2, 2014
Ceras Victoria (Honda Prelude), Salvage (Part III)
Did a bit more work today.
Removed the center console, all boot covers, the dashboard climate control sliders / center vents, stereo head unit, and rear seats.
As usual the aesthetic bolt covers (this time on the rear passenger side sear) were much more difficult to get off than the bolt or seat itself. Again, seats are being save potentially to make a couch or something out of as they will not be used in Nausicaa, the project Prelude.
Rear portion of center console out, personally, I like the arm rest / storage compartment more than I like the one from Nausicaa which lacks them:

Removed the center console, all boot covers, the dashboard climate control sliders / center vents, stereo head unit, and rear seats.
As usual the aesthetic bolt covers (this time on the rear passenger side sear) were much more difficult to get off than the bolt or seat itself. Again, seats are being save potentially to make a couch or something out of as they will not be used in Nausicaa, the project Prelude.
Rear portion of center console out, personally, I like the arm rest / storage compartment more than I like the one from Nausicaa which lacks them:
Saturday, February 1, 2014
Ceras Victoria (Honda Prelude), Salvage (Part II)
As mentioned in Ceras Victoria, Salvage (Part I) I mentioned that I was unable to remove the passenger front seat.
Here's why:
Here's why:
Sunday, January 26, 2014
Ceras Victoria (Honda Prelude), Salvage (Part I)
Friday, January 24, 2014
Cagalli Yula (Subaru BRZ), One Week Review
I've owned Cagalli Yula [2014 Subaru BRZ Limited] for one week now.
After driving her for a day I took her on a trip back to Chicago through a blizzard. She's a bit messy, I do not seem to have any coin washes in the area, but I do have one car wash with great reviews nearby, so, hopefully she'll be clean by Sunday.
In terms of driving experience, at first she was very very stiff and bumpy. Now, either I've gotten used to it or she's loosened up some.
Steering wise she is very responsive, you feel everything. I compare driving her and the feel you get as the difference between sneakers and Vibram FiveFingers on your feet. We've had some snow and ice and I have no complaints so far. The Continental Extreme Contact DWS tires are doing their job.
After driving her for a day I took her on a trip back to Chicago through a blizzard. She's a bit messy, I do not seem to have any coin washes in the area, but I do have one car wash with great reviews nearby, so, hopefully she'll be clean by Sunday.
In terms of driving experience, at first she was very very stiff and bumpy. Now, either I've gotten used to it or she's loosened up some.
Steering wise she is very responsive, you feel everything. I compare driving her and the feel you get as the difference between sneakers and Vibram FiveFingers on your feet. We've had some snow and ice and I have no complaints so far. The Continental Extreme Contact DWS tires are doing their job.
Friday, October 25, 2013
Ceras Victoria (Honda Prelude) 200,000 Mile Birthday
Ceras Victoria his her 200,000th mile on October 25th, 2013.
It took 19 years (possibly 20) as she is a 1994 Honda Prelude Si.
I'd like to say there are many more ahead of her, but that's highly unlikely and she'll soon be heading for the scrap heap.
Here are the photos of her odometer.
200,000 miles!
It took 19 years (possibly 20) as she is a 1994 Honda Prelude Si.
I'd like to say there are many more ahead of her, but that's highly unlikely and she'll soon be heading for the scrap heap.
Here are the photos of her odometer.
200,000 miles!Sunday, October 6, 2013
Ceras Victoria (Honda Prelude), Throttle Position Sensor
So my friend and colleague, Aaron, suggests that he's had similar problems to mine and that I should replace the throttle position sensor. This being a less than $30 part I figure, what the heck, I need the car to run well until mid December, I'll give it a try, the forums say this is pretty easy...
(And that should have been a warning...)
(And that should have been a warning...)
Friday, September 20, 2013
More Test Drives of the Subaru Product Line
Today
I tested more cars offered by Subaru. I went back to Hodges Subaru in Ferndale,
MI and was dealing with Danielle again (if you’re looking to buy a Subaru and
live in the Detroit area, deal with her, she’s wonderful!). Today I was testing
and measuring cars for my parents who are finally looking to replace Harmony
(2000 Subaru Outback) or Cloud (1999 Subaru Forester).
A
few notes on the Subaru product line before I review the cars. Subaru needs to
offer a wagon version of the Legacy that is less bulky looking than the new
Outback’s (this is available in Japan and should be here too). Subaru manual
transmission vehicles still suffer from very soft clutch pedals, a bit more
resistant would just let you know you’re pressing it better. Also, Subaru offers
a lot of great diesel versions of their vehicles in other countries that are
quite fuel efficient, these should be offered to the USA as well.
On
to the cars I drove today:
Monday, September 9, 2013
Ceras Victoria (Honda Prelude), Tune Up Adendum
So, the car was running a bit rough on the way back from Toronto and even worse as time went on.
During the tune up I may have messed up a little in removing a stuck and rusted rotor that would not come off its spindle. The wires inside the distributor cap were damaged. (Did not know this when I took it to the dealership.)
I had it towed to LaFontaine Honda figuring if the cap, rotor, or distributor coil were bad a Honda dealership would be the most likely to have them in stock, and my girlfriend and I were planning to drive up to Toronto.
Fast forward a week or so later. It was getting unbearable, so I popped the hood.
The top bolt from the distributor cap was gone leaving a small gap, quite possibly causing incomplete burn or miss fires.
Also, they apparently took off the air intake pipe and put it back together wrong. There was a gap between the air box connect and the pipe letting unfiltered air in. The hose clamp by the throttle body was also ridiculously loose. Last time I take a car there, ever.
During the tune up I may have messed up a little in removing a stuck and rusted rotor that would not come off its spindle. The wires inside the distributor cap were damaged. (Did not know this when I took it to the dealership.)
I had it towed to LaFontaine Honda figuring if the cap, rotor, or distributor coil were bad a Honda dealership would be the most likely to have them in stock, and my girlfriend and I were planning to drive up to Toronto.
Fast forward a week or so later. It was getting unbearable, so I popped the hood.
The top bolt from the distributor cap was gone leaving a small gap, quite possibly causing incomplete burn or miss fires.
Also, they apparently took off the air intake pipe and put it back together wrong. There was a gap between the air box connect and the pipe letting unfiltered air in. The hose clamp by the throttle body was also ridiculously loose. Last time I take a car there, ever.
Friday, August 30, 2013
Ceras Victoria (Honda Prelude), Tune Up
Replaced the cap, rotor, spark plugs, spark plug wires, and air filter.
Car was running pretty darn smooth.
Drove it to Toronto, Canada with the girlfriend to visit a friend. (Note: never tell the border guards that you're there to visit your gaming friend... it leads to additional questioning.)
After a week though (this post is being written on 9/8/2013) there are some issues back again, it is still acting like there is a restriction plate.
That said, it was nice to have it running well for at least one trip.
Car was running pretty darn smooth.
Drove it to Toronto, Canada with the girlfriend to visit a friend. (Note: never tell the border guards that you're there to visit your gaming friend... it leads to additional questioning.)
After a week though (this post is being written on 9/8/2013) there are some issues back again, it is still acting like there is a restriction plate.
That said, it was nice to have it running well for at least one trip.
Saturday, August 17, 2013
Ceras Victoria (Honda Prelude), CV Axles
Saturday, August 10, 2013
Ceras Victoria (Honda Prelude), Motor Mounts (Part 2)
So, fixing the rear motor mount was a bit on the tough side. Last weekend I tried to do this myself and I did not succeed.
Two of my coworkers assisted me, special thanks to Jason and Daniel.
In the foreground there's a piece of slag from the break bar. The break bar was dropped across the battery terminals resulting in some sparks and a bit of fire. Luckily it didn't drain much from the battery.

Two of my coworkers assisted me, special thanks to Jason and Daniel.
In the foreground there's a piece of slag from the break bar. The break bar was dropped across the battery terminals resulting in some sparks and a bit of fire. Luckily it didn't drain much from the battery.
Friday, July 26, 2013
Tools (Part 1)
I still need to replace the rear motor mount on Ceras Victoria. Shops were quoting me $250 - $400 base, and if you read the reviews of the shops it was likely to be much more.
So, rather than paying someone else to do it I figured I'd dump the money into tools that will work now and let me get other things done in the future.
One such tool is an air compressor from Craftsman. 26 gallon, so, not huge, but decent enough for what I need, and a 20 gallon increase over the tiny pancake my dad has.
Ordinarily I would not consider this newsworthy, but I should let the pictures do the talking:

So, rather than paying someone else to do it I figured I'd dump the money into tools that will work now and let me get other things done in the future.
One such tool is an air compressor from Craftsman. 26 gallon, so, not huge, but decent enough for what I need, and a 20 gallon increase over the tiny pancake my dad has.
Ordinarily I would not consider this newsworthy, but I should let the pictures do the talking:
Monday, July 1, 2013
Ceras Victoria (Honda Prelude), Motor Mounts (Part 1)
Thursday, January 10, 2013
Ceras Victoria (Honda Prelude), Timing Belt (Attempt 1)
I went to do the timing belt on my car which did not end up
happening. The last time a timing belt was done it seems like a mechanic used
seize or lock tight on the pulley bolt (most likely) or cross threaded the
whole thing.
So, despite having a professional grade 1/2" and
3/4" drive air gun at my disposal, the 3/4" meant to work on medium
and large trucks, we were unable to get the bolt to budge. In fact, we had
around 400 lb. ft. on a bolt that was
only supposed to be torqued to 180 lb. ft.
Needless to say, timing belt, front main oil seal, and water
pump did not happen. The lower timing belt could not be removed.
The day was not a total waste though. I wound up replacing
the spark plugs, valve cover gasket (little leaky) and valve cover grommets (much
more leaky) all before having a misfire.
Also discovered that the camshaft seals need to be replaced,
but those cannot be done without being able to have full access to the timing
chain.
I may try the belt again when it is warmer. Otherwise, and
at the moment, it looks like the timing belt will not be coming out without
removing the crankshaft. Oh joy!
My family friend Norman was helping me out with this.
Thursday, August 30, 2012
Ceras Victoria (Honda Prelude), Car Alarm Removal
Ceras Victoria had an aftermarket Clifford fancy alarm installed in her just after I bought her. I wanted a good car alarm.
The problem is as time has gone on I have not driven her much, especially being in law school and using public transportation every day.
I drive the car maybe once a week, more likely once a month. This means I use fuel stabilizer in the tank a lot and that the internal battery on the car alarm goes dead.
I disconnect the battery when I park it because there is an electrical drain (possibly was the alarm) so that I can start it when I need to.
The disconnecting of the battery meant that every time I reconnected the battery the car alarm treated it as a break in. This means that it goes in super shut down ignition kill mode which is just a pain in the ass. So, when it did this while I was visiting family in New Jersey with my girl friend (was supposed to be a short visit, turned out much longer) I decided the alarm had to go.
Luckily I had my camera with me.
Seat removed to make it easier to access the dash.
The problem is as time has gone on I have not driven her much, especially being in law school and using public transportation every day.
I drive the car maybe once a week, more likely once a month. This means I use fuel stabilizer in the tank a lot and that the internal battery on the car alarm goes dead.
I disconnect the battery when I park it because there is an electrical drain (possibly was the alarm) so that I can start it when I need to.
The disconnecting of the battery meant that every time I reconnected the battery the car alarm treated it as a break in. This means that it goes in super shut down ignition kill mode which is just a pain in the ass. So, when it did this while I was visiting family in New Jersey with my girl friend (was supposed to be a short visit, turned out much longer) I decided the alarm had to go.
Luckily I had my camera with me.
Seat removed to make it easier to access the dash.
Subscribe to:
Posts (Atom)

